Preparation and characterization of Cf/Pollucite composites through geopolymer precursors

Continuous carbon-fibre-reinforced Cs-geopolymer composite (C_f/CsGP) were prepared, and its in-situ conversion was investigated during high-temperature treatments. The effect of treatment temperature on the thermal evolution process and mechanical properties of the resulting products were systematically evaluated. The results indicated that the crystallization temperature of C_f/CsGP composite was considerably delayed because the amorphous structure of carbon fibres was not conducive as a nucleation substrate for pollucite derived from the CsGP matrix. Moreover, the integrity of the corresponding resulting products derived from the C_f/CsGP composite were damaged due to thermal shrinkage that occurred during the high-temperature treatment process. When treatment temperature was ≤1200^oC, the mechanical properties of the corresponding products exhibited an upward trend, which was ascribed to the improvement of the densification degree of the resulting composite and well interface-bonding state between carbon fibres and pollucite. However, the mechanical properties of the resulting composites decreased with the treatment temperature continued increased from 1200 to 1400^oC. This phenomenon was attributed to the impairment of fibre properties caused by interfacial reactions.     

混菌矿化增强再生粗骨料的物理力学性能

为克服单一微生物培养成本高且矿化鲁棒性不足的缺陷，提出了一种混菌矿化增强再生粗骨料物理力学性能的方法.通过筛选矿化效率较高的好氧嗜碱混菌，考察了混菌矿化对再生粗骨料物理力学性能和混凝土抗压强度的影响.结果表明：相同增强时间下，混菌比纯菌呈现出更优异的矿化增强效果；随着混菌矿化增强时间的延长，再生粗骨料吸水率和压碎指标呈现出先减小后增大的趋势，最优增强时间为15 d；采用矿化增强再生粗骨料制备的再生混凝土抗压强度提高幅度达到22.1%.     

UV-enhanced conductive and dielectric properties in KTN crystal

We observe enhancements of both conductive and dielectric properties under UV illumination by using a ferroelectric absorber, potassium tantalate niobate (KTa_1-xNb_xO₃, KTN). The UV-generated electron-hole pairs weaken the intrinsic ferroelectric polarization while enhance the conductive property. The UV-induced heat effect causes the enhancement of the dielectric property. The results are further confirmed by the maximal rectification ratio which shows an opposite trend between the direct heating process and the UV illumination. Our results are useful for better understanding of ferroelectric properties under UV illumination and the development of new optoelectronic devices.     

改性聚乳酸发泡技术研究进展

综述了近几年国内外改性聚乳酸（PLA）发泡技术的研究进展，针对PLA在发泡方面熔体强度和结晶性能的不足，介绍了通过加入扩链剂、交联剂、成核剂、纤维和其他聚合物等物质来改善PLA发泡性能的方法、效果和机理；最后，对改性聚乳酸发泡技术的未来发展进行了展望。     

Preparation and Characterization of Hydrophobic Bagasse Hemicellulose-based Films

To improve the hydrophobicity of bagasse hemicellulose-based films, glutaraldehyde was applied when preparing films of original and cationic bagasse hemicellulose with the addition of polyvinyl alcohol and sorbitol. The results showed that the cationic modification could increase the hydrophobicity of the hemicellulose-based film, and the hydrophobicity of hemicellulose-based films crosslinked with glutaraldehyde also increased. However, cationic modification of hemicellulose decreased the stress of the hemicellulose-based film. While crosslinking with glutaraldehyde increased the stress of both the original and cationic hemicellulose-based films. Macrophotography indicated that the film formability of the original hemicellulose was better than that of cationic hemicellulose. Through SEM observation, the degree of bonding of different components of the films was found to be increased due to crosslinking with glutaraldehyde. The crosslinking reaction between glutaraldehyde and hemicellulose was further confirmed by FT-IR spectroscopy.     

掺合料对超高性能水泥基装饰材料性能的影响

将重钙粉与偏高岭土以不同的比例混合并替代白水泥，制备超高性能水泥基装饰材料,研究两者掺入比例变化对超高性能水泥基装饰材料工作性能、力学性能及自收缩的影响，采用SEM扫描电镜观察28 d龄期后试件内部微观形貌，研究表明，随着重钙粉与偏高岭土比例的增大，试件的致密程度和强度先增后减，其中B9-9的28 d抗压与抗折强度可以达到120.6 MPa与42.9 MPa，且工作性、收缩性能良好、内部结构致密。     

Time and space dependence of large-scale synthesis of colloidal particle with special morphology and tuneable polymer film architecture

This paper describes a facile method to control the morphology of polymer colloids and the architecture of polymer film via miniemulsion polymerization. By taking advantage of cyclization between the symmetrical diacrylate cross-linker hexamethylene diacrylate (HDDA) and the pendent vinyl in colloidal particles, the morphology of polymer colloids and the architecture of the after-formed polymer film were able to be well controlled by tuning the loading of cross-linker HDDA and crosslinking time. Four kinds of polymer colloid morphologies and four kinds of film architecture (honeycomb, close-packed, loose-packed, and enhanced-honeycomb) were characterized by TEM. The film formation mechanisms behind them were proposed based on the special and interesting results including Z-average size of the colloidal particles, Mc (molecular weight between crosslinking points) and mechanical properties of polymer film. Our results highly suggested that the morphology of polymer colloids and the polymer film architecture together determine the adhesive properties of the colloidal polymer film. The best of 180°-peel resistance, T-peel resistance and shear resistance of the polymer films were 138.12 N/25 mm, 40.98 N/25 mm and 25.72 N/cm² at 2.0 phm, 2.0 phm and 0.4 phm with the same crosslinking time of 90 min, respectively. The proposed method is promising to be scaled up for industrial production due to its well adaptability.     

Practical Application of the Probabilistic‐Statistical Model of the Suspension Separation in Hydrocyclones

An effective practical approach that allows not only a significant reduction in the scope of practical experiments in the course of studying suspension separation processes in hydrocyclones, but also makes it possible to assess the intensity of random components of the processes and define the interrelation between such components and hydrodynamics of flows in a hydrocyclone is presented. Within the frames of the developed probabilistic‐statistical model of suspension separation in hydrocyclones on the basis of statistical self‐similarity properties, a relationship was found between determined and random components of the processes. This allowed transitioning from three‐parameter probability density functions for suspension particles in hydrocyclones to two‐parameter functions; thus significantly improving the efficiency of practical application of the developed model.